+86 0516 85628519

2026-10-28
CNC machining defects include unwanted burrs, damaged surfaces and dimensions or geometry that fail the applicable part requirements. Diagnosing them starts with identifying the affected feature, establishing when the condition appears and comparing measurements taken under equivalent conditions. The corrective action should follow the evidence: similar marks or dimensional errors can develop through different mechanisms.
A burr is a condition on the workpiece. Tool wear, a built-up edge or unstable cutting may help explain how it formed, but naming one of those mechanisms does not prove the cause. Recording the location, machining stage and development of an abnormal condition makes the investigation more useful than a general description such as “poor finish.”
WLD manufactures construction machinery structural components and includes CNC machining in its manufacturing scope. For this class of product, a useful quality discussion identifies the particular machined face, hole or connection feature and the requirements that apply to it.
Begin with the requirement the feature must satisfy. A visible tool pattern may be acceptable on one surface and unacceptable on another. A smooth-looking face may still have a dimensional or geometric error. The drawing, applicable specification and agreed inspection condition establish the basis for deciding whether the observed condition is a machining nonconformity.
Describe the problem in terms that another person can locate and reproduce. “The bore is inaccurate” leaves open whether the issue is diameter, taper, roundness, axis direction or position relative to a datum. “The diameter changes between the entrance and a deeper section under the same inspection setup” gives the investigation a defined starting point. It still needs comparison with the specified requirements and an appropriate measurement method.
The detection stage matters as much as the location. A scratch first recorded after machining, cleaning and transport cannot automatically be assigned to the cutting operation. Compare observations from the earliest available stage to establish whether the damage was already present. Preserve the surface before polishing or reworking it, because those actions may remove useful evidence.
Separate three statements in the investigation record: what was observed, which requirement was not met and which causes remain possible. A photograph can document where a mark lies; it cannot establish a bore axis or demonstrate the flatness of an entire mounting face. Similarly, an average roughness reading does not describe every local scratch. Select evidence that answers the specific question being investigated.
Burrs are unwanted projections of material left attached to a cut edge. A specified chamfer or radius is an intentional feature, so the first check is whether the edge condition actually departs from the drawing. Through-holes can have burrs at both the entrance and exit, and the two sides should be recorded separately.
The location helps decide what to investigate. An exit burr directs attention to the tool’s breakthrough condition and the edge produced there. Burrs that become more pronounced as a tool is used justify reviewing its cutting-edge condition alongside the material and cutting conditions. Neither observation establishes a cause on its own.
| Observed pattern | Useful next comparison | Conclusion to avoid |
| Burr concentrated at a through-hole exit | Compare entry and exit edges, breakthrough conditions and the condition of the cutting edge. | Assuming the entire hole requires the same process change. |
| Burr grows across successive parts | Relate edge observations to tool use, material records and recorded process changes. | Declaring tool wear solely from the production sequence. |
| Burr changes after a tool replacement | Check whether geometry, tool setting or cutting conditions changed at the same time. | Attributing every improvement to a sharper edge. |
Useful records include the feature location, cutting direction, entry and exit sides, tool identification and the stage at which the edge was examined. Take a close view of the burr and a wider view showing its position on the part. This allows an engineer to connect the local appearance with the actual operation.
Reducing burr formation and removing an existing burr are separate tasks. Changes to tooling or cutting conditions must suit the material and operation. Deburring must also preserve the specified hole mouth, edge profile and adjacent surfaces. Removing excess material until an edge feels smooth can produce an oversized chamfer or damage a functional face. The final edge geometry needs verification as well as the absence of the unwanted burr.
Repeated waves or bands on a milled surface can be a sign of vibration during cutting, but ordinary feed marks also form patterns. Compare the observed surface with its acceptance requirements, then examine where the abnormal pattern begins and ends. A photograph records the texture; process observations and tool inspection help explain it.
Map the marks to the toolpath. If they appear mainly in internal corners or during a change in direction, investigate changes in cutter engagement and cutting load. If they occur throughout a pass, review conditions that persist throughout that pass, including tool condition, tool holding and the stability of the workpiece. These are priorities for investigation, not a rule that each location identifies one cause.
A worn cutting edge can increase cutting forces. A long tool assembly can be more susceptible to movement. More teeth engaging the workpiece or a sudden increase in engagement can also change the load. Evidence from the affected cut should determine which factor deserves attention before changing workholding or cutting conditions.
Reducing feed is not a universal cure for chatter. In some milling conditions, an excessively small chip load can contribute to unstable cutting. Review spindle speed, feed, cutter geometry and engagement together, using the applicable tool recommendations as a starting point. A controlled change should be evaluated against the surface and dimensions it produces, without assuming that slower settings must improve the result.
Irregular tearing or a smeared appearance warrants a different line of investigation. A built-up edge occurs when workpiece material adheres near the tool’s cutting edge and alters the effective cutting condition. Inspecting the tool may reveal adhesion that supports this explanation. The appearance of the workpiece alone cannot confirm it, because edge damage and other cutting conditions can also impair the surface.
Keep adhesion, wear and chipping distinct. Wear develops through deterioration of the working edge; chipping involves local edge breakage. They can affect cutting differently and may coexist. Record what is present on the tool before selecting a replacement or changing the process. A damaged edge can be an effect of instability, so replacing it may improve the next cut without resolving the original source of the problem.
Chip recutting is another possibility when chips remain in the cutting zone. Examine chip evacuation and any local edge damage alongside the workpiece marks. Random scratches also require a check of cleaning and handling stages. If the surface was acceptable when it left the machine and was damaged later, changing cutting parameters addresses the wrong stage.
The practical decision is to match an intervention to a supported mechanism. Evidence of excessive wear may justify replacing the edge and reviewing its use interval. Marks concentrated at load changes may justify evaluating engagement and toolpath conditions. Adhesion may call for reviewing the tool and cutting conditions for that material. Each response still requires a controlled check of the resulting feature.
A hole can have an acceptable diameter at one section while its shape or location remains incorrect. Hole size, form and position therefore need separate descriptions. The inspection method should be capable of evaluating the stated requirement; a simple diameter reading cannot demonstrate every aspect of roundness, taper or axis location.
Where appropriate, compare measurements at different depths and directions to investigate whether the geometry changes through the hole. The number and placement of measurements depend on the feature and required evaluation. Avoid treating a convenient reading near the entrance as representative of the complete bore.
Tool deflection, wear and cutting conditions can affect the form produced when enlarging or interpolating a hole. A common positional shift across several features raises different questions about work coordinates, locating references and setup changes. Review the size and location results separately before changing compensation. A size adjustment does not, by itself, verify that the feature is correctly positioned relative to the specified datums.
WLD’s Excavator Lower Frame includes longitudinal beams, an X-frame and a slewing-support mounting seat. That arrangement provides a practical reference for identifying a specific interface within a larger fabricated structure. Any machining or inspection requirement for such an interface must be tied to its project drawing; the product name alone cannot define the acceptance limits.
Arrange measurements in the order the parts or features were machined, and mark relevant events such as a tool change, offset edit or new setup. A stable deviation present from the first measured part deserves a different investigation from a gradual trend or a sudden step. The pattern helps organize the evidence, while the event history helps test possible explanations.
| Dimensional pattern | Evidence to compare | What the pattern cannot prove |
| Several features share a similar positional shift | Common references, work coordinates, locating condition and program or setup revisions. | That the machine itself lacks sufficient accuracy. |
| A dimension drifts during a production run | Tool use, machine state, part temperature and the timing and method of measurement. | That wear or thermal drift is the sole cause. |
| A sudden change follows a tool or setup change | All settings and physical conditions changed at that event, with comparable before-and-after results. | That the last recorded action alone caused the deviation. |
| Diameter readings differ along the hole | Measurements at the required depths and directions, together with the tool condition and hole-making operation. | That a diameter measured near the entrance describes the complete hole form. |
| Results change after unclamping or changing supports | Support and restraint, measurement references, temperature and the specified inspection state. | That residual stress is the cause, or that the clamped reading represents the delivered condition. |
Keep machining heat and measurement temperature separate. Heat within a machine can alter its geometry during processing. After machining, the workpiece, reference artefact and measuring equipment may also be at different temperatures, affecting dimensional comparison. An unchanged room-temperature reading does not establish that all three are in equivalent thermal states.
Record relevant temperature and timing information when investigating drift or a disagreement between shop and inspection results. Do not prescribe one waiting period for every part: the measurement task and actual conditions determine what is needed. When results lie close to an acceptance limit, the suitability and uncertainty of the measurement also deserve review.
A change after unclamping needs similar care. Check whether the two measurements used comparable supports and the required inspection condition. Elastic release, changing support contact, temperature and other changes in the workpiece state may need investigation. The difference alone does not establish a residual-stress problem or justify a standard heat-treatment remedy.
A useful hypothesis specifies both a possible mechanism and an observation that could challenge it. “Tool wear may be contributing because the condition worsens with tool use” is testable. “The tooling is unsuitable” is too broad unless the investigation identifies the relevant tool condition and how a change will be evaluated.
Consider a hypothetical milling operation where the surface improves after a tool change. If the replacement also has a shorter overhang, the test has changed both the cutting edge and the tool assembly geometry. The improvement supports further investigation, but it does not isolate wear as the cause. A useful record makes that distinction clear instead of closing the issue on the strength of one improved surface.
Immediate correction may be necessary to protect production, yet the record should distinguish an effective change from a verified explanation. This makes later recurrence easier to investigate and avoids treating temporary improvement as proof that every contributing condition has been removed.
Correcting the process for the next part does not establish that previously machined parts are acceptable. Their disposition depends on the actual condition and the applicable engineering and quality requirements. Separate the plan for preventing recurrence from the decision about each affected part or identified group of parts.
For rework that removes material, check the remaining size and geometry before proceeding. An oversized hole cannot be restored to its original diameter by further cutting, and polishing an already undersized shaft removes more of the material needed to meet the requirement. A scratch may be removable only at the cost of violating another dimension or surface requirement.
| Proposed action | Condition to establish first | Reinspection focus |
| Remove a burr | The permitted edge profile and a method that preserves the intended feature. | Residual burrs, hole-mouth or edge geometry and damage to adjacent faces. |
| Remachine a surface or hole | Sufficient permitted material remains, and the proposed route can meet all affected requirements. | Size, form, location and relevant surface condition after release into the specified inspection state. |
| Polish or blend local damage | The treatment is permitted and will preserve the required dimensions and function. | The treated region and any resulting change in profile, texture or edge condition. |
Material addition, repair or a change to the acceptance basis requires its own engineering review and appropriate approval. Those options should not be assumed available simply because further cutting is unsuitable. Document the approved disposition and the checks needed to demonstrate that it has been achieved.
For a recurring issue, also examine whether the correction remains effective across the relevant conditions. One satisfactory part immediately after an adjustment may not represent later tool use, a restarted machine or another setup. Select the verification scope to address the circumstances in which the original condition appeared.
A well-founded investigation moves from an identified feature to comparable evidence, then to a tested correction and a verified part. When discussing a fabricated component with WLD, share your structural-part requirements together with the drawing, feature locations and relevant inspection conditions. That information gives the technical discussion a concrete basis and keeps acceptance connected to the part’s intended function.